Photo resistor

Kimi K3.1 Pro$0.312m 43s2m 39s waiting on the model3 builds

Reference
iso
front
back
top
bottom
left
right

100of 100

built: 100
geometry: 100
AI judge: 7 of 7

What the AI judge checked

Pass:The overall form matches the reference: the same kind of object, the same silhouette from the matching angle
- Opus 5.5: pass: The top view shows a long rectangular housing with two diagonally opposed tabbed flanges, matching the reference silhouette from above.
- GPT-6 Sol: pass: The renders show the reference’s long rectangular housing with two mounting flanges on opposite sides.
Pass:Proportions match: the relative sizes of the major dimensions agree with the reference within what the eye can judge
- Opus 5.5: pass: The body length-to-width ratio is about 3.2:1 in the top view, close to the reference body, and the flange sizes relative to the body look similar.
- GPT-6 Sol: pass: The body’s length-to-width ratio and the flange sizes appear close to those in the photo.
Pass:Every major feature visible in the reference (holes, slots, bosses, tabs, lips) is present in the result
- Opus 5.5: pass: The finned or grooved body and two flanges with round holes are all present.
- GPT-6 Sol: pass: Both holed mounting flanges and the longitudinal grooves visible in the reference are present.
Pass:Those features sit where the reference has them
- Opus 5.5: pass: One flange sits at the top near the right end and the other at the bottom near the left end, as in the photo, with longitudinal grooves near both long edges.
- GPT-6 Sol: pass: The flanges sit near opposite ends and on opposite long sides, as they do in the reference.
Pass:Nothing is present that the reference does not show — no decorative or unexplained geometry
- Opus 5.5: pass: No extra geometry beyond the body, grooves and the two flanges is visible.
- GPT-6 Sol: pass: The renders show no unexplained features beyond the housing, grooves, and mounting flanges.
Pass:A rectangular finned extrusion with a flat base, grooved along both long sides — not a cylinder or a plain block
- Opus 5.5: pass: The body is a rectangular extrusion with a flat base and longitudinal slots running along both long sides of the top, not a cylinder.
- GPT-6 Sol: pass: The part is a flat-based rectangular prism with longitudinal grooves along both long edges.
Pass:No wires, lugs or terminals modelled at either end
- Opus 5.5: pass: Neither end shows any wires, lugs or terminals; the end faces are plain.
- GPT-6 Sol: pass: No wires, lugs, or terminals are modeled at either end.

Measured

✓ watertight: ok
✓ one sub-part named housing: ok
✓ length is 50 mm: ok
✓ width over the flanges: ok
✓ height is 15.39 mm: ok
✓ two through-holes: ok
✓ the -X flange hole clears 3.7 mm: ok
✓ the -X flange is there around its hole: ok
✓ the -X flange is on one side only: ok
✓ the -X hole is 3.7 mm, not a slot: ok
✓ the +X flange hole clears 3.7 mm: ok
✓ the +X flange is there around its hole: ok
✓ the +X flange is on one side only: ok
✓ the +X hole is 3.7 mm, not a slot: ok
✓ the leads were not modelled: ok

Loading the transcript…

This is an older run. See the current results.

Run kimi31-sonnet-hard2026-11-05commit 58201d93spend $50.99 + $14.79 AI judgingOther runs: 2026-11-05T05-50-12-kimi31-vs-sonnet, 2026-10-16T18-49-10-hard-compact-2026-10-16, 2026-09-23T06-56-16-hard-baseline-2026-09-23, 2026-09-10T19-44-23-baseline-2026-09, 2026-09-04T20-02-10-stage2-hard-cases, 2026-09-04T19-48-31-screen-14-fixed