Photo resistor

Kimi K3.1 Pro$0.242m 13s2m 11s waiting on the model1 build

Reference
iso
front
back
top
bottom
left
right

97of 100

built: 100
geometry: 100
AI judge: 6 of 7

What the AI judge checked

Pass:The overall form matches the reference: the same kind of object, the same silhouette from the matching angle
- Opus 5.5: pass: The top view shows a long rectangular grooved body with two diagonally opposed tabbed flanges, matching the photo's silhouette.
- GPT-6 Sol: pass: The renders show the same elongated rectangular housing with two opposing mounting flanges and longitudinal edge grooves.
Pass:Proportions match: the relative sizes of the major dimensions agree with the reference within what the eye can judge
- Opus 5.5: pass: The body length-to-width ratio is about 3.3:1, and the flange tab sizes are similar to those in the photo.
- GPT-6 Sol: pass: The body’s length-to-width ratio and the flange sizes appear close to the reference.
Pass:Every major feature visible in the reference (holes, slots, bosses, tabs, lips) is present in the result
- Opus 5.5: pass: The longitudinal grooves and both flanges with round holes are present.
- GPT-6 Sol: pass: Both mounting flanges have holes, and grooves run along both long edges of the body.
Fail:Those features sit where the reference has themAI judges disagreed
- Opus 5.5: pass: In the top view, one flange sits at the upper right and the other at the lower left at base level, matching the photo.
- GPT-6 Sol: fail: Both mounting flanges sit noticeably farther inward from the body ends than they do in the reference.
Pass:Nothing is present that the reference does not show — no decorative or unexplained geometry
- Opus 5.5: pass: No extra geometry beyond the body, the grooves and the flanges is visible.
- GPT-6 Sol: pass: The renders show no unexplained geometry beyond the housing, grooves, and mounting flanges.
Pass:A rectangular finned extrusion with a flat base, grooved along both long sides — not a cylinder or a plain block
- Opus 5.5: pass: It is a rectangular extrusion with a flat base (bottom view) and grooves running lengthwise along both long edges, as seen in the top and end views.
- GPT-6 Sol: pass: The part is a rectangular prism with a flat base and longitudinal grooves along both long edges.
Pass:No wires, lugs or terminals modelled at either end
- Opus 5.5: pass: No wires, lugs or terminals appear at either end in any render.
- GPT-6 Sol: pass: No wires, solder lugs, or terminals appear at either end.

Measured

✓ watertight: ok
✓ one sub-part named housing: ok
✓ length is 50 mm: ok
✓ width over the flanges: ok
✓ height is 15.39 mm: ok
✓ two through-holes: ok
✓ the -X flange hole clears 3.7 mm: ok
✓ the -X flange is there around its hole: ok
✓ the -X flange is on one side only: ok
✓ the -X hole is 3.7 mm, not a slot: ok
✓ the +X flange hole clears 3.7 mm: ok
✓ the +X flange is there around its hole: ok
✓ the +X flange is on one side only: ok
✓ the +X hole is 3.7 mm, not a slot: ok
✓ the leads were not modelled: ok

Loading the transcript…

This is an older run. See the current results.

Run kimi31-sonnet-hard2026-11-05commit 58201d93spend $50.99 + $14.79 AI judgingOther runs: 2026-11-05T05-50-12-kimi31-vs-sonnet, 2026-10-16T18-49-10-hard-compact-2026-10-16, 2026-09-23T06-56-16-hard-baseline-2026-09-23, 2026-09-10T19-44-23-baseline-2026-09, 2026-09-04T20-02-10-stage2-hard-cases, 2026-09-04T19-48-31-screen-14-fixed