Photo resistor

Sonnet 5.5, effort high$0.1053s52s waiting on the model1 build

Reference
iso
front
back
top
bottom
left
right

87of 100

built: 100
geometry: 73
AI judge: 7 of 7

What the AI judge checked

Pass:The overall form matches the reference: the same kind of object, the same silhouette from the matching angle
- Opus 5.5: pass: The top view shows a long rectangular grooved body with two diagonally opposite tabbed flanges, matching the photo's silhouette.
- GPT-6 Sol: pass: The renders show a long finned resistor housing with two mounting flanges, matching the reference’s overall silhouette without the leads.
Pass:Proportions match: the relative sizes of the major dimensions agree with the reference within what the eye can judge
- Opus 5.5: pass: The body length-to-width ratio is about 3.2:1 in the top view, close to the roughly 3.3:1 seen in the photo, and the flange sizes look comparable.
- GPT-6 Sol: pass: The body’s length-to-width ratio and the relative size of the flanges appear close to the reference.
Pass:Every major feature visible in the reference (holes, slots, bosses, tabs, lips) is present in the result
- Opus 5.5: pass: Both mounting flanges with holes and the longitudinal grooves are present.
- GPT-6 Sol: pass: Both mounting flanges, their through-holes, and longitudinal grooves are visible.
Pass:Those features sit where the reference has them
- Opus 5.5: pass: One flange projects from the upper edge near the right end and the other from the lower edge near the left end, as in the photo.
- GPT-6 Sol: pass: The holed flanges sit near opposite ends on opposite long sides, as in the reference.
Pass:Nothing is present that the reference does not show — no decorative or unexplained geometry
- Opus 5.5: pass: No extra geometry beyond the grooved body and two flanges appears in the renders.
- GPT-6 Sol: pass: The renders show no unexplained additions beyond the housing, grooves, and mounting flanges.
Pass:A rectangular finned extrusion with a flat base, grooved along both long sides — not a cylinder or a plain block
- Opus 5.5: pass: The end view shows a flat-based rectangular extrusion notched with grooves on both long sides and the top.
- GPT-6 Sol: pass: The body is a rectangular prism with a flat base and grooves running along both long sides.
Pass:No wires, lugs or terminals modelled at either end
- Opus 5.5: pass: Neither end shows any wires, lugs or terminals.
- GPT-6 Sol: pass: No wires, solder lugs, or terminals appear at either end.

Measured

✓ watertight: ok
✓ one sub-part named housing: ok
✓ length is 50 mm: ok
✗ width over the flanges: predicate returned false
✗ height is 15.39 mm: predicate returned false
✓ two through-holes: ok
✓ the -X flange hole clears 3.7 mm: ok
✓ the -X flange is there around its hole: ok
✓ the -X flange is on one side only: ok
✗ the -X hole is 3.7 mm, not a slot: predicate returned false
✓ the +X flange hole clears 3.7 mm: ok
✓ the +X flange is there around its hole: ok
✓ the +X flange is on one side only: ok
✗ the +X hole is 3.7 mm, not a slot: predicate returned false
✓ the leads were not modelled: ok

Loading the transcript…

This is an older run. See the current results.

Run kimi31-sonnet-hard2026-11-05commit 58201d93spend $50.99 + $14.79 AI judgingOther runs: 2026-11-05T05-50-12-kimi31-vs-sonnet, 2026-10-16T18-49-10-hard-compact-2026-10-16, 2026-09-23T06-56-16-hard-baseline-2026-09-23, 2026-09-10T19-44-23-baseline-2026-09, 2026-09-04T20-02-10-stage2-hard-cases, 2026-09-04T19-48-31-screen-14-fixed