Photo resistor

Sonnet 5.5, effort high$0.141m 0s58s waiting on the model3 builds, 1 failed

Reference
iso
front
back
top
bottom
left
right

96of 100

built: 85
geometry: 100
AI judge: 7 of 7

What the AI judge checked

Pass:The overall form matches the reference: the same kind of object, the same silhouette from the matching angle
- Opus 5.5: pass: The render shows an elongated rectangular housing with two diagonally opposed tabbed flanges, matching the top-down silhouette of the resistor in the photo.
- GPT-6 Sol: pass: The renders show a long rectangular resistor housing with longitudinal fins and two opposing mounting flanges, matching the reference silhouette.
Pass:Proportions match: the relative sizes of the major dimensions agree with the reference within what the eye can judge
- Opus 5.5: pass: The top view's body length-to-width ratio of about 3.2:1 matches the photo, and the end view is roughly square, consistent with a 15.39 mm height.
- GPT-6 Sol: pass: The body's length-to-width ratio and the flange sizes appear close to those in the reference.
Pass:Every major feature visible in the reference (holes, slots, bosses, tabs, lips) is present in the result
- Opus 5.5: pass: The body has longitudinal grooves, and both mounting flanges with through holes are present.
- GPT-6 Sol: pass: Both mounting flanges have holes, and the body has longitudinal grooves and raised lips.
Pass:Those features sit where the reference has them
- Opus 5.5: pass: In the top view one flange sits at the upper-right and the other at the lower-left, matching the photo, and both are at base level.
- GPT-6 Sol: pass: The flanges sit near opposite ends on opposite long sides, as in the reference.
Pass:Nothing is present that the reference does not show — no decorative or unexplained geometry
- Opus 5.5: pass: Only the grooved body and two holed flanges are modelled, with no extra geometry.
- GPT-6 Sol: pass: The renders show no unexplained features beyond the housing, grooves, and mounting flanges.
Pass:A rectangular finned extrusion with a flat base, grooved along both long sides — not a cylinder or a plain block
- Opus 5.5: pass: The body is a flat-based rectangular extrusion with grooves along both long sides and the top, visible in the end and isometric views.
- GPT-6 Sol: pass: The housing is a rectangular extrusion with a flat base and grooves running along both long sides.
Pass:No wires, lugs or terminals modelled at either end
- Opus 5.5: pass: No wires, lugs or terminals appear at either end in any view.
- GPT-6 Sol: pass: No wires, solder lugs, or terminals are modelled at either end.

Measured

✓ watertight: ok
✓ one sub-part named housing: ok
✓ length is 50 mm: ok
✓ width over the flanges: ok
✓ height is 15.39 mm: ok
✓ two through-holes: ok
✓ the -X flange hole clears 3.7 mm: ok
✓ the -X flange is there around its hole: ok
✓ the -X flange is on one side only: ok
✓ the -X hole is 3.7 mm, not a slot: ok
✓ the +X flange hole clears 3.7 mm: ok
✓ the +X flange is there around its hole: ok
✓ the +X flange is on one side only: ok
✓ the +X hole is 3.7 mm, not a slot: ok
✓ the leads were not modelled: ok

Loading the transcript…

This is an older run. See the current results.

Run kimi31-sonnet-hard2026-11-05commit 58201d93spend $50.99 + $14.79 AI judgingOther runs: 2026-11-05T05-50-12-kimi31-vs-sonnet, 2026-10-16T18-49-10-hard-compact-2026-10-16, 2026-09-23T06-56-16-hard-baseline-2026-09-23, 2026-09-10T19-44-23-baseline-2026-09, 2026-09-04T20-02-10-stage2-hard-cases, 2026-09-04T19-48-31-screen-14-fixed